Gas Hazards in Battery Power Storage

Batteries are effective at reducing power outages since they can also store excess traditional grid energy. The energy stored within batteries can be released whenever a large volume of power is needed, such as during a power failure at a data centre to prevent data being lost, or as a back-up power supply to a hospital or military application to ensure the continuity of vital services. Large scale batteries can also be used to plug short-term gaps in demand from the grid. These battery compositions can also be used in smaller sizes to power electric cars and may be further scaled down to power commercial products, such as phones, tablets, laptops, speakers and – of course – personal gas detectors.

Gas hazards

The main gas risk emitted by batteries, specifically lead acid batteries, is hydrogen. It is possible to get both hydrogen and oxygen evolved during charging however, a lead acid battery is likely to have catalytic recombination parts internally, so oxygen is less of a risk. Hydrogen is always a cause for concern, as it can collect and build up. A situation that is obviously worsened when they are charged in a space with a poor airflow.

When charging, lead-acid batteries consist of lead and oxide at the positive terminal, and of spongy lead at the negative anode, using concentrated sulfuric acid as the electrolyte. The presence of sulfuric acid is another cause for concern if the battery leaks or is ever damaged because concentrated acids harm people, metals and the environment.

When charging batteries also emit oxygen and hydrogen because of the electrolysis process. The levels of hydrogen produced soar when a lead acid battery cell “blows” or is unable to be charged properly. The amount of gas present is relevant because high levels of hydrogen make it highly explosive, even though it is not toxic. Hydrogen has a 100% lower explosive limit of 4.0% by volume, at which level an ignition source would cause fires or for hydrogen more usually, explosions. Fires and explosions are an issue not only for the workers within the space, but also for the surrounding equipment and infrastructure.

Importance of Gas Detection Technology

Gas detection is an invaluable safety technology often equipped in battery charging rooms. Ventilation is also advised, and while helpful, it is not fool proof as fan motors can fail and should not be relied upon as the sole safety measure for battery charging areas. Fans mask the problem while gas detection notifies personnel to act before problems escalate. Gas detection systems are crucial in informing personnel of increasing gas leaks before becoming dangerous. Gas detection units comply with local building codes and NFPA 111, the National Fire Protection Association standard on stored electrical energy emergency and standby power systems. They include maintenance, operation, installation, and testing provisions regarding the system’s performance. In addition to permanent gas detection systems, handheld units are available. The benchmark products are provided by Crowcon and are listed below.

Portable Gas Detectors

Crowcon’s portable gas detectors (Gasman, Gas-Pro, T4x, Tetra 3 and T4) protect against a wide range of industrial gas hazards, with both single gas and multi-gas monitors available. With a wide range of sizes and complexities, you can find the right portable gas detection solution to meet the number and type of gas sensors you need and your display and certification requirements.

Fixed Gas Detectors

Crowcon gas detection fixed systems offer a flexible range of solutions that can measure flammable, toxic, and oxygen gases, report their presence, and activate alarms or associated equipment. Crowcon fixed gas monitoring systems (Xgard, Xgard Bright and XgardIQ) are designed to be interfaced with manual call points, fire and gas detectors, and distributed control systems (DCS).

Control Panels

Crowcon gas detection control panels offer a flexible range of solutions that can measure flammable, toxic, and oxygen gases, report their presence, and activate alarms or associated equipment. Crowcon fixed gas (Vortex, GM Addressable Controllers, Gasmaster) monitoring systems are designed to be interfaced with manual call points, fire and gas detectors and distributed control systems (DCS). In addition, each system can be engineered to drive remote annunciators and mimic panels. Crowcon has a gas detection product to suit your application regardless of your operation.

Temperature Measurement

Crowcon has extensive experience with temperature measurement. There are several models of temperature measurement, from pocket thermometers to industrial kits ranging from -99.9 to 299.9°C with probes and clamps. They are enhancing their fixed detection capabilities by adding high-temperature electrochemical sulphur dioxide detection for battery manufacturing and charging stations. This is critical during the first charge of a battery, as a fault is most likely at that time. Their fast-acting systems detect the precursors to thermal runaway and quickly terminate power to the batteries to avoid damage.

To find out more on the dangers of gas hazards in battery power visit our industry page for more information.

Xgard Type 3: The mV Advantage

Xgard Type 3 is the ideal solution for detecting lighter-than-air flammable gases such as methane and hydrogen. Detectors in such applications usually have to be mounted high-up in roof spaces or above equipment where access for calibration and maintenance is  likely to present problems.

Gas detectors require calibration (usually every six months) and sensors may need to be replaced every 3-5 years. These activities usually require direct access to the detector to make adjustments and replace parts. National regulations such as the ‘UK Work at Height Regulations 2005’ stipulate safe working practices when working on equipment at height, and compliance usually requires the use of scaffolding or mobile ‘cherry pickers’ which entails significant cost and disruption on-site.

The advantage of mV pellistor type detectors

The terms ‘mV’ and ‘4-20mA’ describe the type of signal which is transmitted through the cable between the gas detector and the control system (for example a Crowcon Gasmaster). Calibration of  4-20mA detector (e.g. Xgard Type 5) entails removing the lid, and zeroing/calibrating the amplifier using a meter, test-points and potentiometers. Even more sophisticated detectors with a display and non-intrusive calibration still require direct access to operate the menu system using a magnet in order to perform calibration.

Xgard Type 3 is a mV pellistor-based detector which has no internal electronics (i.e. no amplifier); just terminals to connect via three wires to the control system (e.g. Gasmaster). Commissioning simply entails measuring the ‘head voltage’ at the detector terminals, and performing zero and calibration adjustments at the Gasmaster input module. Ongoing 6-monthly calibrations are then performed by remotely applying gas (via a ‘spray deflector’ or ‘collector cone’ accessory), and any necessary adjustments are made at ground level via the control system input module.

Hence once commissioned, mV pellistor type detectors do not need to be accessed until the sensor needs replacing; usually 3-5 years after installation. The routine need for expensive access equipment; scaffolding or cherry-pickers in thus avoided.

Xgard Type 3 can be directly connected to Gasmaster and Gasmonitor systems, and to Vortex via an ‘Accessory Enclosure’ accessory which converts the mV signals to 4-20mA.

Remote calibration of a mV pellistor type detector
Remote calibration of a mV pellistor type detector.

The importance of Gas Detection in the Water and Wastewater Industry 

Water is vital to our daily lives, both for personal and domestic use and industrial/commercial applications. Whether a facility focuses on the production of clean, potable water or treating effluent, Crowcon is proud to serve a wide variety of water industry clients, providing gas detection equipment that keeps workers safe around the world. 

Gas Hazards 

Apart from common gas hazards known in the industry; methane, hydrogen sulphide, and oxygen, there are bi-product gas hazards and cleaning material gas hazards that occur from purifying chemicals such as ammonia, chlorine, chlorine dioxide or ozone that are used in the decontamination of the waste and effluent water, or to remove microbes from clean water. There is great potential for many toxic or explosive gases to exist as a result of the chemicals used in the water industry. And added to these are chemicals that may be spilled or dumped into the waste system from industry, farming or building work. 

Safety Considerations  

Confined Space Entry 

The pipelines used to transport water require regular cleaning and safety checks; during these operations, portable multi-gas monitors are used to protect the workforce. Pre-entry checks must be completed prior to entering any confined space and commonly O2, CO, H2S and CH4 are monitored. Confined spaces are small, so portable monitors must be compact and unobtrusive for the user, yet able to withstand the wet and dirty environments in which they must perform. Clear and prompt indication of any increase in gas monitored (or any decrease for oxygen) is of paramount importance – loud and bright alarms are effective in raising the alarm to the user. 

Risk assessment 

Risk assessment is critical, as you need to be aware of the environment that you are entering and thus working in. Therefore, understanding the applications and identifying the risks regarding all safety aspects. Focusing on gas monitoring, as part of the risk assessment, you need to be clear on what gases may be present.  

Fit for purpose 

There is a variety of applications within the water treatment process, giving the need to monitor multiple gases, including carbon dioxide, hydrogen sulphide, chlorine, methane, oxygen, ozone and chlorine dioxide. Gas detectors are available for single or multiple gas monitoring, making them practical for different applications as well as making sure that, if conditions change (such as sludge is stirred up, causing a sudden increase in hydrogen sulphide and flammable gas levels), the worker is still protected.  

Legislation   

European Commission Directive 2017/164 issued in January 2017, established a new list of indicative occupational exposure limit values (IOELVs). IOELV are health-based, non-binding values, derived from the most recent scientific data available and considering the availability of reliable measurement techniques. The list includes carbon monoxide, nitrogen monoxide, nitrogen dioxide, sulphur dioxide, hydrogen cyanide, manganese, diacetyl and many other chemicals. The list is based on Council Directive 98/24/EC that considers the protection of the health and safety of workers from the risks related to chemical agents in the workplace. For any chemical agent for which an IOELV has been set at Union level, Member States are required to establish a national occupational exposure limit value. They also are required to take into account the Union limit value, determining the nature of the national limit value in accordance with national legislation and practice. Member States will be able to benefit from a transitional period ending at the latest on 21 August 2023.  

The Health and Safety Executive (HSE) state that each year several workers will suffer from at least one episode of work-related illness. Although, most illnesses are relatively mild cases of gastroenteritis, there is also a risk for potentially fatal diseases, such as leptospirosis (Weil’s disease) and hepatitis. Even though these are reported to the HSE, there could be significant under-reporting as there is often failure to recognise the link between illness and work.  

Under domestic law of the Health and Safety at Work etc Act 1974, employers are responsible for ensuring the safety of their employees and others. This responsibility is reinforced by regulations. 

The Confined Spaces Regulations 1997 applies where the assessment identifies risks of serious injury from work in confined spaces. These regulations contain the following key duties: 

  • Avoid entry to confined spaces, e.g., by doing the work from the outside. 
  • If entry to a confined space is unavoidable, follow a safe system of work.
  • Put in place adequate emergency arrangements before the work start. 

The Management of Health and Safety at Work Regulations 1999 requires employers and self-employed people to carry out a suitable and sufficient assessment of the risks for all work activities for the purpose of deciding what measures are necessary for safety. For work in confined spaces this means identifying the hazards present, assessing the risks and determining what precautions to take. 

Our solutions

Elimination of these gas hazards is virtually impossible, so permanent workers and contractors must depend on reliable gas detection equipment to protect them. Gas detection can be provided in both fixed and portable forms. Our portable gas detectors protect against a wide range of gas hazards, these include T4x, Clip SGD, Gasman, Tetra 3,Gas-Pro, T4 and Detective+. Our fixed gas detectors are used in many applications where reliability, dependability and lack of false alarms are instrumental to efficient and effective gas detection, these include Xgard, Xgard Bright and IRmax. Combined with a variety of our fixed detectors, our gas detection control panels offer a flexible range of solutions that measure flammable, toxic and oxygen gases, report their presence and activate alarms or associated equipment, for the wastewater industry our panels include  Gasmaster.    

To find out more on the gas hazards in wastewater and water treatment visit our industry page for more information.  

Gas Safety Protocols in Water Treatment

Water is vital to our daily lives, both for personal and domestic use and industrial/commercial applications. It is everywhere, promoting some chemical reactions and inhibiting others. Being used to clean surfaces, carry chemicals to where they are used and to carry unwanted chemicals away. Do anything and you create a gas somewhere in some quantity. Do anything with water there are so many permutations of things that can come together and react, dissolved gases that can come out of solution, dissolved liquids and solids that can react to generate gases. Additionally, you must determine what gases you generate when you collect, clean, store, transport or use water. Gas detectors must be chosen to suit the specific environment in which they operate, in this case highly humid, often dirty, but rarely outside the temperature range 4 to 30 degrees C. All the risks are present in these complex environments, with multiple toxic and flammable gas hazards and often the additional risk of oxygen depletion.

Gas Hazards

Apart from common gas hazards known in the industry; methane, hydrogen sulphide, and oxygen, there are bi-product gas hazards and cleaning material gas hazards that occur from purifying chemicals such as ammonia, chlorine, chlorine dioxide or ozone that are used in the decontamination of the waste and effluent water, or to remove microbes from clean water. There is great potential for many toxic or explosive gases to exist as a result of the chemicals used in the water industry. And added to these are chemicals that may be spilled or dumped into the waste system from industry, farming or building work.

Chlorine (Cl2) gas appears yellow green in colour, used to sterilise drinking water. However, most chlorine is used in the chemical industry with typical applications including water treatment as well as within the plastics and cleaning agents. Chlorine gas can be recognised by its pungent, irritating odour, which is like the odour of bleach. The strong smell may provide adequate warning to people that they are exposed. Cl2 itself is not flammable, but it can react explosively or form flammable compounds with other chemicals such as turpentine and ammonia.

Ammonia (NH3) is a compound of nitrogen and hydrogen and is a colourless and pungent gas, also known to be highly soluble when in contact with water. This means that NH3 dissolves quickly into the water supply. Found at very low levels in humans and in nature. It is also often used in some household cleaning solutions. Although NH3 has many benefits, it can be corrosive and dangerous in certain circumstances. Ammonia can enter wastewater from several different sources, including urine, manure, cleaning chemicals, process chemicals and amino acid products. If NH3 enters a copper piping system, it can cause extensive corrosion. If NH3 enters water, its toxicity varies depending on the exact pH of the water. It is possible for ammonia to break down into ammonium ions, which can react with other compounds present.

Chlorine dioxide (ClO2) is an oxidising gas commonly used to disinfect drinking water. When used in very small quantities, it is safe and does not lead to significant health risks. But ClO2 is a strong disinfectant that kills bacteria, viruses, and fungi, and when used in high doses, it can be dangerous to people since it can damage red blood cells and the lining of the gastrointestinal (GI) tract.

Ozone (O3) is a gas with an antiseptic smell and no colour that, mostly, forms naturally in the environment. When inhaled, ozone can have a range of harmful effects on the body. As it is colourless gas it is difficult to trace without an effective detection system in place. Even when relatively small amounts are inhaled, the gas can have a damaging impact on the respiratory tract, causing inflammation and chest pain, alongside coughing, shortness of breath and throat irritation. It can also act as a trigger causing diseases such as asthma to worsen.

Confined Space Entry

The pipelines used to transport water require regular cleaning and safety checks; during these operations, portable multi-gas monitors are used to protect the workforce. Pre-entry checks must be completed prior to entering any confined space and commonly O2, CO, H2S and CH4 are monitored. Confined spaces are small, so portable monitors must be compact and unobtrusive for the user, yet able to withstand the wet and dirty environments in which they must perform. Clear and prompt indication of any increase in gas monitored (or any decrease for oxygen) is of paramount importance – loud and bright alarms are effective in raising the alarm to the user.

Legislation

European Commission Directive 2017/164 established an increased list of indicative occupational exposure limit values (IOELVs). IOELV are health-based, non-binding values, derived from the most recent scientific data available and considering the availability of reliable measurement techniques. Non-binding but best practice. The list includes carbon monoxide, nitrogen monoxide, nitrogen dioxide, sulphur dioxide, hydrogen cyanide, manganese, diacetyl and many other chemicals. The list is based on Council Directive 98/24/EC that considers the protection of the health and safety of workers from the risks related to chemical agents in the workplace. For any chemical agent for which an IOELV has been set at Union level, Member States are required to establish a national occupational exposure limit value. They also are required to take into account the Union limit value, determining the nature of the national limit value in accordance with national legislation and practice. Member States will be able to benefit from a transitional period ending at the latest on 21 August 2023.

The Health and Safety Executive (HSE) state that each year several workers will suffer from at least one episode of work-related illness. Although, most illnesses are relatively mild cases of gastroenteritis, there is also a risk for potentially fatal diseases, such as leptospirosis (Weil’s disease) and hepatitis. Even though these are reported to the HSE, there could be significant under-reporting as there is often failure to recognise the link between illness and work.

Under domestic law of the Health and Safety at Work etc Act 1974, employers are responsible for ensuring the safety of their employees and others. This responsibility is reinforced by regulations.

The Confined Spaces Regulations 1997 applies where the assessment identifies risks of serious injury from work in confined spaces. These regulations contain the following key duties:

  • Avoid entry to confined spaces, e.g., by doing the work from the outside.
  • If entry to a confined space is unavoidable, follow a safe system of work.
  • Put in place adequate emergency arrangements before the work start.

The Management of Health and Safety at Work Regulations 1999 requires employers and self-employed people to carry out a suitable and sufficient assessment of the risks for all work activities for the purpose of deciding what measures are necessary for safety. For work in confined spaces this means identifying the hazards present, assessing the risks and determining what precautions to take.

Our solution

Elimination of these gas hazards is virtually impossible, so permanent workers and contractors must depend on reliable gas detection equipment to protect them. Gas detection can be provided in both fixed and portable forms. Our portable gas detectors protect people against a wide range of gas hazards, and include T4x, Clip SGD, Gasman, Tetra 3, Gas-Pro, T4 and Detective+. Our fixed gas detectors are used where reliability, dependability and lack of false alarms are instrumental to efficient and effective protection of assets and areas, and include the Xgard, Xgard Bright and IRmax product ranges. Combined with a variety of our fixed detectors, our gas detection control panels offer a flexible range of solutions that measure flammable, toxic and oxygen gases, report their presence and activate alarms or associated equipment, for the wastewater industry we often recommend our Gasmaster panel.

To find out more on the gas hazards in wastewater visit our industry page for more information.

Gas Hazards in Wastewater

Water is vital to our daily lives, both for personal and domestic use and industrial/commercial applications making water sites both numerous and widespread. Despite the quantity and location of water sites, only two environments predominate, and these are quite specific. They are clean water and wastewater. This blog details gas risks encountered at wastewater sites and how they may be mitigated. 

The wastewater industry is always wet, with temperatures between 4 and 20oc near the water and rarely far from that limited temperature range even away from the immediate location of the wastewater. 90%+ relative humidity, 12 +/- 8oc, atmospheric pressure, with multiple toxic and flammable gas hazards and the risk of oxygen depletion. Gas detectors must be chosen to suit the specific environment in which they operate, and whilst high humidity is generally challenging to all instrumentation, the constant pressure, moderate temperatures and narrow temperature range is a far greater benefit to safety instrumentation. 

Gas Hazards  

The main gases of concern in wastewater treatment plants are:

Hydrogen sulphide, methane and carbon dioxide are the by-products of the decomposition of organic materials that exist in the waste flows feeding the plant. The build-up of these gases may lead to the lack of oxygen, or in some cases, explosion when coupled with a source of ignition. 

Hydrogen sulphide (H2S)

Hydrogen sulphide is a common product of the biodegradation of organic matter; pockets of H2S can collect in rotting vegetation, or sewage itself, and be released when disturbed. Workers in sewerage and wastewater plants and pipework can be overcome by H2S, with fatal consequences. Its high toxicity is the main danger of H2S. Prolonged exposure to 2-5 parts per million (ppm) H2S can cause nausea and headaches and bring tears to the eyes. H2S is an anaesthetic, hence at 20ppm, symptoms include fatigue, headaches, irritability, dizziness, temporary loss of the sense of smell and impaired memory. Severity of symptoms increase with concentration as nerves shut down, through coughing, conjunctivitis, collapse and rapid unconsciousness. Exposure at higher levels can result in rapid knock down and death. Prolonged exposure to low levels of H2S may cause chronic illness or can also kill. Because of this, many gas monitors will have both instantaneous and TWA (Time-Weighted Average) alerts. 

Methane (CH4)

Methane is a colourless, highly flammable gas that is the primary component of natural gas, also referred to as biogas. It can be stored and/or transported under pressure as a liquid-gas. CH4 is a greenhouse gas that is also encountered in normal atmospheric conditions at a rate of approximately 2 parts per million (ppm). High exposure can lead to slurred speech, vision problems and memory loss. 

Oxygen (O2)

The normal concentration of oxygen in the atmosphere is approximately 20.9% volume. In the absence of adequate ventilation, the level of oxygen can be reduced surprisingly quickly by breathing and combustion processes. Olevels may also be depleted due to dilution by other gases such as carbon dioxide (also a toxic gas), nitrogen or helium, and chemical absorption by corrosion processes and similar reactions. Oxygen sensors should be used in environments where any of these potential risks exist. When locating oxygen sensors, consideration needs to be given to the density of the diluting gas and the “breathing” zone (nose level). 

Safety Considerations 

Risk assessment

Risk assessment is critical, as you need to be aware of the environment that you are entering and thus working in. Therefore, understanding the applications and identifying the risks regarding all safety aspects. Focusing on gas monitoring, as part of the risk assessment, you need to be clear on what gases may be present. 

Fit for purpose

There is a variety of applications within the water treatment process, giving the need to monitor multiple gases, including carbon dioxide, hydrogen sulphide, chlorine, methane, oxygen, ozone and chlorine dioxide. Gas detectors are available for single or multiple gas monitoring, making them practical for different applications as well as making sure that, if conditions change (such as sludge is stirred up, causing a sudden increase in hydrogen sulphide and flammable gas levels), the worker is still protected. 

Legislation  

European Commission Directive 2017/164 issued in January 2017, established a new list of indicative occupational exposure limit values (IOELVs). IOELV are health-based, non-binding values, derived from the most recent scientific data available and considering the availability of reliable measurement techniques. The list includes carbon monoxide, nitrogen monoxide, nitrogen dioxide, sulphur dioxide, hydrogen cyanide, manganese, diacetyl and many other chemicals. The list is based on Council Directive 98/24/EC that considers the protection of the health and safety of workers from the risks related to chemical agents in the workplace. For any chemical agent for which an IOELV has been set at Union level, Member States are required to establish a national occupational exposure limit value. They also are required to take into account the Union limit value, determining the nature of the national limit value in accordance with national legislation and practice. Member States will be able to benefit from a transitional period ending at the latest on 21 August 2023. 

The Health and Safety Executive (HSE) state that each year several workers will suffer from at least one episode of work-related illness. Although, most illnesses are relatively mild cases of gastroenteritis, there is also a risk for potentially fatal diseases, such as leptospirosis (Weil’s disease) and hepatitis. Even though these are reported to the HSE, there could be significant under-reporting as there is often failure to recognise the link between illness and work. 

Our solutions  

Elimination of these gas hazards is virtually impossible, so permanent workers and contractors must depend on reliable gas detection equipment to protect them. Gas detection can be provided in both fixed and portable forms. Our portable gas detectors protect against a wide range of gas hazards, these include T4x, Clip SGD, Gasman, Tetra 3, Gas-Pro, T4 and Detective+. Our fixed gas detectors are used where reliability, dependability and lack of false alarms are instrumental to efficient and effective gas detection, these include Xgard, Xgard Bright and IRmax. Combined with a variety of our fixed detectors, our gas detection control panels offer a flexible range of solutions that measure flammable, toxic and oxygen gases, report their presence and activate alarms or associated equipment, for the wastewater industry our panels include Gasmaster.   

To find out more on the gas hazards in wastewater visit our industry page for more information. 

What are the dangers of gas in telecommunications?

The telecommunication industry contains includes cable providers, internet service providers, satellite providers and telephone providers and confined spaces. Even simple above ground termination boxes may contain gas hazards generated from the cable runs underground. Gases such as methane, carbon dioxide and hydrogen sulphide can run through cable trunking accumulating in termination boxes and manifesting as hazards when the termination box is opened.

The risk of danger occurs when a worker is sent to carry out tasks involving opening up of enclosed volumes that may not have been accessed for a period of time. All telecommunications companies have these in abundance.

What are the Dangers?

Those working in the telecommunications industry are at risk from a variety of gaseous dangers, many of which could cause harm to their health and safety. Though less obvious, these risks should be taken as seriously as falls from heights or electrocution, and they require a similar level of training. A worker must not climb to an elevated position without a harness, similarly they shouldn’t be accessing confined spaces without appropriate confined space training. Awareness of the dangers present and minimising the risks that could lead to adverse effects is a well-known safety principle. Training and proper PPE can help protect workers from these hazards.

Gas Hazards and Risks

As there are many confined spaces in the telecommunication industry workers are at risk from the presence of hazardous and toxic gases there. Hazardous gases can also be linked to seemingly simple above-ground termination boxes. Gases such as methane, carbon dioxide and hydrogen sulphide sometimes travel through the cable trunking, and therefore, when the termination box is opened, a build-up of these gases can be released.

Enclosed or partially enclosed spaces with high levels of methane in the air reduce the amount of oxygen available to breathe and therefore can cause mood changes, speech and vision problems, memory loss, nausea, sickness, facial flushing and headaches. In more severe cases and prolonged exposure, there may be changes in breathing and heart rate, balance problems, numbness, and unconsciousness. There is also a risk of fire as methane is highly flammable.

Carbon monoxide (CO) consumption also poses serious health issues to workers, with those ingesting the toxic substance facing flu-like symptoms, chest pain, confusion, fainting arrhythmias, seizures, or even worse health effects for high or long lasting exposures. Hydrogen sulphide (H2S) poisoning causes similar issues, as well as delirium, tremors, convulsions, and skin and eye irritation. Carbon dioxide is an asphyxiant gas that can displace oxygen and hance dizziness.

Our solution

Gas detection can be provided in both fixed and portable forms. Our portable gas detectors protect against a wide range of gas hazards, these include Tetra 3 and T4. Our fixed gas detectors are used where reliability, dependability and lack of false alarms are instrumental to efficient and effective gas detection, these include Xgard and Xgard Bright. Combined with a variety of our fixed detectors, our gas detection control panels offer a flexible range of solutions which are able to measure flammable, toxic and oxygen gases, report their presence and activate alarms or associated equipment, for the telecommunication industry our panels include Gasmaster.

To find out more on the dangers of gas hazards in telecommunication visit our industry page for more information.

Transportation and Key Gas Challenges 

The transportation sector is one of the largest industries in the world, spanning a variety of applications. The sector offers services concerned with the movement of people and cargo of all types, across air freight and logistics, airlines and airport services, road and rail, transportation infrastructure, trucking, highways, rail tracks, and marine ports and services.

Gas hazards during transportation  

The transport of dangerous goods is regulated in order to prevent, accidents involving people or property, damage to the environment. There a numerous gas hazards including the transportation of hazardous material, air conditioning emissions, cabin combustion and hangar leaks. 

The transportation of hazardous materials poses a risk to those involved. There are nine classification areas specified by the United Nations (UN) including explosives, gases, flammable liquids and solids, oxidising substances, toxic substances, radioactive materials, corrosive substances and miscellaneous goods. With the risk of an accident occurring being more likely when transporting these materials. Although the biggest cause for concern within the industry being the transportation of non-flammable non-toxic gas is asphyxiation. As a slow leak in a storage container can drain all of the oxygen in the air and cause the individuals in the environment to suffocate. 

Leaks within aircraft hangars and fuel storage areas of highly explosive aviation fuel is an area that must be monitored to prevent fires, equipment damage, and at the worst fatalities. It is essential to choose a suitable gas detection solution that focuses on the aircraft rather than the aircraft hangar, avoids false alarms, and can monitor large areas. 

Not only is it the external environment that faces gas risks in transportation, those working in the sector also face similar challenges. Air conditioning emissions poses a gas hazard threat due to the burning of fossil fuels leading to a subsequent emission of carbon monoxide (CO). high levels of CO in a confined area such as a vehicle cabin, of more than the normal level (30ppm) or an oxygen level below normal (19%) can result in dizziness, feeling and being sick, tiredness and confusion, stomach pain, shortness of breath and difficulty breathing. Therefore, proper ventilation in these spaces with the assistance of a gas detector is paramount to ensuring the safe of those working in the transportation industry. 

Similarly, in the air sector cabin combustion and fuselage fires, in the central portion of an airplane, poses a real threat. Although flame retardant materials are applied, if a fire does start the cabin’s trim and fittings can still generate toxic gases and vapours that could be more dangerous than the fire itself. Inhalation of harmful gases caused by a fire in these environments tend to be the main direct cause of fatalities.

Transportation Standards and Certifications 

Each mode of transport, (road, rail, air, sea and inland waterway) has its own regulations but they are generally harmonized with the United Nations Economic Commission for Europe (UNECE). The Hazardous Materials Transportation Act (HMTA), enacted in the USA in 1975, states that regardless of the type of transportation, any company whose goods fall into one of the nine categories specified as hazardous by the UN, must comply with the regulations or risk fines and penalties. 

Those working in the transport sector in the UK must comply with the requirements laid out in the UN Model Regulations which assigns each dangerous substance or article a specific class that correlates how dangerous it is. It does this via the packing group (PG) classification, according to PG I, PG II or PG III. 

From an European standpoint the International Carriage of Dangerous Goods by Road (ADR) governs the regulations on how to classify, pack, label and certify dangerous goods. It also comprises vehicle and tank requirements and other operational requirements. The Carriage of Dangerous Goods and Use of Transportable Pressure Equipment Regulations (2009) also is relevant in England, Wales and Scotland. 

Other relevant regulations include the International Carriage of Dangerous Goods by Inland Navigation (ADN), the International Maritime Dangerous Goods (IMDG) and The International Civil Aviation Organization’s (ICAO) Technical Instruction.

Our solution 

Gas detection can be provided in both fixed and portable forms. Our portable gas detectors protect against a wide range of gas hazards, these include T4x, Clip SGD, Gasman, Tetra 3, Gas-pro, and T4. Our fixed gas detectors are used where reliability, dependability and lack of false alarms are instrumental to efficient and effective gas detection, these include Xgard, Xgard Bright, and IRmax. Combined with a variety of our fixed detectors, our gas detection control panels offer a flexible range of solutions which are able to measure flammable, toxic and oxygen gases, report their presence and activate alarms or associated equipment, for the transportation industry our panels include Gasmaster and Vortex 

To find out more on the dangers of gas hazards in transportation visit our industry page for more information.