Gas-Pro TK: Dual readings of %LEL and %Vol

Gas-Pro TK (re-branded from Tank-Pro) dual range portable monitor measures the concentration of flammable gas in inerted tanks. Available for methane, butane and propane, Gas-Pro TK uses a dual IR flammable gas sensor – the best technology for this specialist environment. Gas-Pro TK dual IR features auto-range switching between %vol. and %LEL measurement, to ensure operation at the correct measurement range. This technology isn’t damaged by high hydrocarbon concentrations and does not need oxygen concentrations to work, as are the limiting factors of catalytic bead/ pellistors in such environments. 

What problem is Gas-Pro TK specifically designed to overcome? 

When you wish to enter a fuel storage tank for inspection or maintenance, you may start with it full of flammable gas. You can’t just start pumping air in to displace the flammable gas because at some point in the transition from only fuel present to only air present, there would be an explosive mixture of fuel and air. Instead, you must pump in an inert gas, usually nitrogen to displace the fuel without introducing oxygen. The transition from 100% flammable gas and 0% volume nitrogen, to 0% volume flammable gas and 100% nitrogen enables a safe transition from 100% nitrogen to air. Using this two-step process enables a safe transition from fuel to air without risking an explosion. 

During this process there is no air or oxygen present, so catalytic bead / pellistor sensors will not work properly and will also be poisoned by the high levels of flammable gas. The dual range IR sensor used by Gas-Pro TK does not require any air or oxygen to function, so it is ideal to monitor the whole of the process, from %volume to %LEL concentrations, while also monitoring oxygen levels in the same environment. 

What is LEL? 

The Lower Explosive Limit (LEL) is the lowest concentration of a gas or vapour that will burn in air. Readings are a percentage of that, with 100%LEL the minimum amount of gas needed to combust. LEL varies from gas to gas, but for most flammable gases it is less than 5% by volume. This means that it takes a relatively low concentration of gas or vapour to produce a high risk of explosion.
Three things must be present for an explosion to occur: combustible gas (the fuel), air and a source of ignition (as shown in the diagram). In addition, the fuel must be present at the right concentration, between the Lower Explosive Limit (LEL), below which the gas/air mixture is too lean to burn, and the Upper Explosive Limit (UEL), above which the mixture is too rich and there is not enough of a supply of oxygen to sustain a flame. 

Safety procedures are generally concerned with detecting flammable gas well before it reaches an explosive concentration, so gas detection systems and portable monitors are designed to initiate alarms before gases or vapours reach the Lower Explosive Limit. Specific thresholds vary according to the application, but the first alarm is typically set at 20% LEL and a further alarm is commonly set to 40% LEL. LEL levels are defined in the following standards: ISO10156 (also referenced in EN50054, which has since been superseded) and IEC60079. 

What is %Volume? 

The percent by volume scale is used to give the concentration of one gas type in a mixture of gases as a percentage of the volume of gas present. It is just a different scale with, for example the methane lower explosive limit concentration is displayed at 4.4% volume instead of 100% LEL or 44000ppm, which are all equivalent. If there was 5% or more methane present in air, we would have a highly dangerous situation where any spark or hot surface could cause an explosion where air (specifically oxygen) is present. If there is 100%volume reading, it means that there is no other gas present in the gas mix. 

Gas-Pro TK 

Our Gas-Pro TK has been designed for use in specialist inerted tank environments to monitor levels of flammable gases and oxygen, as standard gas detectors will not work. In ‘Tank Check Mode’ Our Gas-Pro TK device is suitable for specialist application of monitoring inerted tank spaces during purging or gas freeing, as well as doubles as a regular personal gas safety monitor in normal operation. It enables users to monitor the gas mix in tanks carrying flammable gas during transport at sea (as it is marine approved) or on shore, such as oil tankers and oil storage terminals. At 340g, Gas-Pro TK is up to six times lighter than other monitors for this application; a boon if you have to carry it with you all day. 

In Tank Check mode, the Crowcon Gas-Pro TK, monitors concentrations of flammable gas and oxygen, checking that an unsafe mixture is not developing. The device auto-ranges, switching between %vol and %LEL as gas concentration demands, without manual intervention, and notifies the user as it happens. Gas-Pro TK has real-time oxygen concentrations from within the tank on its display, so users can track the oxygen levels, either for when the oxygen levels are low enough to safely load and store fuel, or high enough for safe tank entry during maintenance. 

The Gas-Pro TK is available calibrated to methane, propane or butane.  With IP65 and IP67 ingress protection, Gas-Pro TK meets the demands of most industrial environments. With optional MED certifications, it is a valuable tool for tank monitoring on-board vessels. The optional High H₂S Sensor addition allows users to analyse possible risk if gases vent during purging. With this option, users can monitor over the 0-100 or 0-1000ppm range. 

Please note: if the fuel in the tank is hydrogen or ammonia, a different gas detection technique is required – and you should contact Crowcon. 

For more information on our Gas-Pro TK visit our product page or get in contact with our team.

How Long will my Gas Sensor Last?

Gas detectors are used extensively within many industries (such as water treatment, refinery, petrochemical, steel and construction to name a few) to protect personnel and equipment from dangerous gases and their effects. Users of portable and fixed devices will be familiar with the potentially significant costs of keeping their instruments operating safely over their operational life. Gas sensors are understood to provide a measurement of the concentration of some analyte of interest, such as CO (carbon monoxide), CO2 (carbon dioxide), or NOx (nitrogen oxide). There are two most used gas sensors within industrial applications: electrochemical for toxic gases and oxygen measurement, and pellistors (or catalytic beads) for flammable gases. In recent years, the introduction of both Oxygen and MPS (Molecular Property Spectrometer) sensors have allowed for improved safety.  

How do I know when my sensor has failed? 

There have been several patents and techniques applied to gas detectors over the past few decades which claim to be able to determine when an electrochemical sensor has failed. Most of these however, only infer that the sensor is operating through some form of electrode stimulation and might provide a false sense of security. The only sure method of demonstrating that a sensor is working is to apply test gas and measure the response: a bump test or full calibration. 

Electrochemical Sensor  

Electrochemical sensors are the most used in diffusion mode in which gas in the ambient environment enters through a hole in the face of the cell. Some instruments use a pump to supply air or gas samples to the sensor. A PTFE membrane is fitted over the hole to prevent water or oils from entering the cell. Sensor ranges and sensitivities can be varied in design by using different size holes. Larger holes provide higher sensitivity and resolution, whereas smaller holes reduce sensitivity and resolution but increase the range. 

Factors affecting Electrochemical Sensor Life 

There are three main factors that affect the sensor life including temperature, exposure to extremely high gas concentrations and humidity. Other factors include sensor electrodes and extreme vibration and mechanical shocks.  

Temperature extremes can affect sensor life. The manufacturer will state an operating temperature range for the instrument: typically -30˚C to +50˚C. High quality sensors will, however, be able to withstand temporary excursions beyond these limits. Short (1-2 hours) exposure to 60-65˚C for H2S or CO sensors (for example) is acceptable, but repeated incidents will result in evaporation of the electrolyte and shifts in the baseline (zero) reading and slower response. 

Exposure to extremely high gas concentrations can also compromise sensor performance. Electrochemical sensors are typically tested by exposure to as much as ten-times their design limit. Sensors constructed using high quality catalyst material should be able to withstand such exposures without changes to chemistry or long-term performance loss. Sensors with lower catalyst loading may suffer damage.  

The most considerable influence on sensor life is humidity. The ideal environmental condition for electrochemical sensors is 20˚Celsius and 60% RH (relative humidity). When the ambient humidity increases beyond 60%RH water will be absorbed into the electrolyte causing dilution. In extreme cases the liquid content can increase by 2-3 times, potentially resulting in leakage from the sensor body, and then through the pins. Below 60%RH water in the electrolyte will begin to de-hydrate. The response time may be significantly extended as the electrolyte or dehydrated. Sensor electrodes can in unusual conditions be poisoned by interfering gases that adsorb onto the catalyst or react with it creating by-products which inhibit the catalyst.  

Extreme vibration and mechanical shocks can also harm sensors by fracturing the welds that bond the platinum electrodes, connecting strips (or wires in some sensors) and pins together.  

‘Normal’ Life Expectancy of Electrochemical Sensor 

Electrochemical sensors for common gases such as carbon monoxide or hydrogen sulphide have an operational life typically stated at 2-3 years. More exotic gas sensor such as hydrogen fluoride may have a life of only 12-18 months. In ideal conditions (stable temperature and humidity in the region of 20˚C and 60%RH) with no incidence of contaminants, electrochemical sensors have been known to operate more than 4000 days (11 years). Periodic exposure to the target gas does not limit the life of these tiny fuel cells: high quality sensors have a large amount of catalyst material and robust conductors which do not become depleted by the reaction. 

Pellistor Sensor 

Pellistor sensors consist of two matched wire coils, each embedded in a ceramic bead. Current is passed through the coils, heating the beads to approximately 500˚C. Flammable gas burns on the bead and the additional heat generated produces an increase in coil resistance which is measured by the instrument to indicate gas concentration. 

Factors affecting Pellistor Sensor Life 

The two main factors that affect the sensor life include exposure to high gas concentration and poising or inhibition of the sensor. Extreme mechanical shock or vibration can also affect the sensor life. The capacity of the catalyst surface to oxidise the gas reduces when it has been poisoned or inhibited. Sensor life more than ten years is common in applications where inhibiting or poisoning compounds are not present. Higher power pellistors have greater catalytic activity and are less vulnerable to poisoning. More porous beads also have greater catalytic activity as their surface volume in increased. Skilled initial design and sophisticated manufacturing processes ensure maximum bead porosity. Exposure to high gas concentrations (>100%LEL) may also compromise sensor performance and create an offset in the zero/base-line signal. Incomplete combustion results in carbon deposits on the bead: the carbon ‘grows’ in the pores and creates mechanical damage. The carbon may however be burned off over time to re-reveal catalytic sites. Extreme mechanical shock or vibration can in rare cases also cause a break in the pellistor coils. This issue is more prevalent on portable rather than fixed-point gas detectors as they are more likely to be dropped, and the pellistors used are lower power (to maximise battery life) and thus use more delicate thinner wire coils. 

How do I know when my sensor has failed? 

A pellistor that has been poisoned remains electrically operational but may fail to respond to gas. Hence the gas detector and control system may appear to be in a healthy state, but a flammable gas leak may not be detected. 

Oxygen Sensor 

Long Life 02 Icon

Our new lead-free, long-lasting oxygen sensor does not have compressed strands of lead the electrolyte has to penetrate, allowing a thick electrolyte to be used which means no leaks, no leak induced corrosion, and improved safety. The additional robustness of this sensor allows us to confidently offer a 5-year warranty for added piece of mind. 

Long life-oxygen sensors have an extensive lifespan of 5-years, with less downtime, lower cost of ownership, and reduced environmental impact. They accurately measure oxygen over a broad range of concentrations from 0 to 30% volume and are the next generation of O2 gas detection. 

MPS Sensor  

MPS sensor provides advanced technology that removes the need to calibrate and provides a ‘True LEL (lower explosive limit)’ for reading for fifteen flammable gases but can detect all flammable gases in a multi-species environment, resulting in lower ongoing maintenance costs and reduced interaction with the unit. This reduces risk to personnel and avoids costly downtime. The MPS sensor is also immune to sensor poisoning.  

Sensor failure due to poisoning can be a frustrating and costly experience. The technology in the MPS™ sensor is not affected by contaminates in the environment. Processes that have contaminates now have access to a solution that operates reliably with fail safe design to alert operator to offer a peace of mind for personnel and assets located in hazardous environment. It is now possible to detect multiple flammable gases, even in harsh environments, using just one sensor that does not require calibration and has an expected lifespan of at least 5 years. 

What’s so Important about my Monitors Measuring Range?

What is a Monitor Measuring Range?

Gas monitoring is usually measured in PPM range (parts per million), percentage volume or percentage of LEL (lower explosive limit) this enables Safety Managers, to ensure that their operators are not being exposed to any potentially harmful levels of gases or chemicals. Gas monitoring can be done remotely to ensure that the area is clean before a worker enters the area as well as monitoring gas through a permanently fixed device or body worn portable device to detect any potentially leaks or hazardous areas during the course of the working shift.  

Why are Gas Monitors essential and what are the Ranges of deficiencies or enrichments?

There are three main reasons why monitors are needed; it is essential to detect oxygen deficiencies or enrichment as too little oxygen can prevent the human body from functioning leading to the worker losing consciousness. Unless the oxygen level can be restored to a normal level the worker is at risk of potential death. An atmosphere is considered to be deficient when the concentration of O2 is less than 19.5%. Consequently, an environment that has too much oxygen in it is equally dangerous as this constitutes a greatly increased risk of fire and explosion, this is considered when the concentration level of O2 is over 23.5%. 

Monitors are required when Toxic Gases are present of which can cause considerable harm to the human body. Hydrogen Sulphide (H2S) is a classic example of this. H2S is given off by bacteria when it breaks down organic matter, due to this gas being heavier than air, it can displace air leading to potential harm to persons present and is also a broad-spectrum toxic poison.  

Additionally, gas monitors have the ability to detect flammable gases. Dangers that can be prevented through using a gas monitor are not only though inhaling but they are a potential hazard due to combustion. gas monitors with an LEL range sensor detects and alert against flammable gases.  

Why are they important and how do they work?

Measurement or Measuring Range is the total range that the device can measure in normal conditions. The term normal meaning no overpressure limits (OPL) and within maximum working pressure (MWP).  These values are usually found on the product website or specification datasheet. The measuring range can also be calculated by identifying the difference between the Upper Range Limit (URL) and the Lower Range Limit (LRL) of the device. When trying to determine the range of the detector it is not identifying the area of square footage or within a fixed radius of the detector but instead is identifying the yielding or diffusion of the area being monitored. The process happens as the sensors respond to the gases that penetrate through the monitor’s membranes. Therefore, the devices have the ability to detect gas that is in immediate contact with the monitor. This  highlights the significance of understanding the measuring range of gas detectors and highlight their importance for the safety of the workers present in these environments.   

Are there any products that are available?

Crowcon offer a range of portable monitors; The Gas-Pro portable multi gas detector offers detection of up to 5 gases in a compact and rugged solution. It has an easy-to-read top mount display making it easy to use and optimal for confined space gas detection. An optional internal pump, activated with the flow plate, takes the pain out of pre-entry testing and allows Gas-Pro to be worn either in pumped or diffusion modes. 

The T4 portable 4-in-1 gas detector provides effective protection against 4 common gas hazards: carbon monoxide, hydrogen sulphide, flammable gases and oxygen depletion. The T4 multi gas detector now comes with improved detection of pentane, hexane and other long chain hydrocarbons. Offering you compliance, robustness and low cost of ownership in a simple to use solution. T4 contains a wide range of powerful features to make everyday use easier and safer. 

The Gasman portable single gas detector is compact and lightweight yet is fully ruggedised for the toughest of industrial environments. Featuring simple single button operation, it has a large easy-to-read display of gas concentration, and audible, visual and vibrating alarms.  

Crowcon also offer a flexible range of fixed gas detection products that can detect flammable, toxic and oxygen gases, report their presence and activate alarms or associated equipment. We use a variety of measurement, protection and communications technologies and our fixed detectors have been proven in many arduous environments, including oil and gas exploration, water treatment, chemical plants and steel mills. These fixed gas detectors are used in many applications where reliability, dependability and lack of false alarms are instrumental to efficient and effective gas detection. These include within the automotive and aerospace manufacturing sectors, on scientific and research facilities and in high-utilisation medical, civil or commercial plants.