Industry Overview: Food and Beverage 

The food and beverage (F&B) industry includes all companies involved in processing raw food materials, as well as those packaging and distributing them. This includes fresh, prepared foods as well as packaged foods, and both alcoholic and non-alcoholic beverages. 

The food and beverage industry is divided into two major segments, which are the production and the distribution of edible goods. The first group, production, includes the processing of meats and cheeses and the creation of soft drinks, alcoholic beverages, packaged foods, and other modified foods. Any product meant for human consumption, aside from pharmaceuticals, passes through this sector. Production also covers the processing of meats, cheeses and packaged foods, dairy and alcoholic beverages. The production sector excludes foods and fresh produce that are directly produced via farming, as these fall under agriculture. 

The manufacture and processing of food and beverages create substantial risks of fire and toxic gas exposure. Many gases are used for baking, processing and refrigerating foods. These gases can be highly hazardous – either toxic, flammable, or both. 

Gas Hazards 

Food Processing

Secondary food processing methods includes fermentation, heating, chilling, dehydration or cooking of some kind. Many types of commercial food processing consist of cooking, especially industrial steam boilers. Steam boilers are usually gas-fired (natural gas or LPG) or use a combination of gas and fuel oil. For gas-fired steam boilers, natural gas consists mainly of methane (CH4), a highly combustible gas, lighter than air, which is piped directly into boilers. In contrast, LPG consists mainly of propane (C3H8), and usually requires an on-site fuel storage tank. Whenever flammable gases are used on site, forced mechanical ventilation must be included in storage areas, in case of leakage. Such ventilation is usually triggered by gas detectors that are installed near boilers and in storage rooms. 

Chemical Disinfection 

The F&B industry takes hygiene very seriously, as the slightest contamination of surfaces and equipment can provide an ideal breeding ground for all kinds of germs. The F&B sector therefore demands rigorous cleaning and disinfection, which must meet industry standards. 

There are three methods of disinfection commonly used in F&B: thermal, radiation and chemical. Chemical disinfection with chlorine-based compounds is by far the most common and effective way to disinfect equipment or other surfaces. This is because chlorine-based compounds are inexpensive, fast acting and effective against a variety of microorganisms. Several different chlorine compounds are commonly used, of which include hypochlorite, organic and inorganic chloramines, and chlorine dioxide. Sodium hypochlorite solution (NaOCl) is stored in tanks while chlorine dioxide (ClO2) gas is usually generated on site.  

In any combination, chlorine compounds are hazardous and exposure to high concentrations of chlorine can cause severe health issues. Chlorine gases are usually stored on site and a gas detection system should be installed, with a relay output to trigger ventilation fans once a high level of chlorine is detected. 

Food Packaging 

Food packaging serves many purposes; it allows food to be transported and stored safely, protects food, indicates portion sizes and provides information about the product. To keep food items safe for a long time, it is necessary to remove oxygen from the container because otherwise, oxidation will occur when the food comes into contact with oxygen. The presence of oxygen also promotes bacterial growth, which is harmful when consumed. However, if the package is flushed with nitrogen, the shelf life of packaged food can be extended. 

Packagers often use nitrogen (N2) flushing methods for preserving and storing their products. Nitrogen is a non-reactive gas, non-odorous and non-toxic. It prevents oxidation of fresh food with sugars or fats, stops the growth of dangerous bacteria and inhibits spoilage. Lastly, it prevents packages from collapsing by creating a pressurized atmosphere. Nitrogen can be generated on site using generators or delivered in cylinders. Gas generators are cost effective and provide an uninterrupted supply of gas. Nitrogen is an asphyxiant, capable of displacing oxygen in air. Because it has no smell and is non-toxic, workers may not become aware of low oxygen conditions before it is too late.  

Oxygen levels below 19% will cause dizziness and loss of consciousness. To prevent this, oxygen content should be monitored with an electrochemical sensor. Installing oxygen detectors in packaging areas ensures the safety of workers and early detection of leaks. 

Refrigeration Facilities 

Refrigeration facilities in the F&B industry are used to keep food cool for long periods of time. Large-scale food storage facilities often use cooling systems based on ammonia (> 50% NH3), as it is efficient and economical. However, ammonia is both toxic and flammable; it is also lighter than air and fills up enclosed spaces rapidly. Ammonia can become flammable if released in an enclosed space where a source of ignition is present, or if a vessel of anhydrous ammonia is exposed to fire.   

Ammonia is detected with electro-chemical (toxic) and catalytic (flammable) sensor technology. Portable detection, including single- or multi-gas detectors, can monitor instantaneous and TWA exposure to toxic levels of NH3. Multi-gas personal monitors have been shown to improve workers’ safety where a low-range ppm for routine system surveys and flammable range is used during system maintenance. Fixed detection systems include a combination of toxic- and flammable-level detectors connected to local control panels – these are usually supplied as part of a cooling system. Fixed systems can also be used for process over-rides and ventilation control. 

Brewing and Drinks Industry 

The risk involved in the manufacture of alcohol involves sizable manufacturing equipment which can be potentially harmful, both to operate and because of the fumes and vapours that can be emitted into the atmosphere and subsequently impact the environment. Ethanol is the main combustible hazard found within distilleries and breweries is the fumes and vapours produced by ethanol. With the capacity to be emitted from leaks in tanks, casks, transfer pumps, pipes and flexible hoses, ethanol vapour is a very real fire and explosion hazard faced by those in the distillery industry. Once the gas and vapour is released into the atmosphere, it can quickly build and pose a danger to the health of workers. It is worth noting here however, that the concentration required to cause harm to workers’ health has to be very high. With this in mind, the more significant risk from ethanol in the air is that of explosion. This fact reinforces the importance of gas detection equipment to recognise and remedy any leaks straight away, so as to avoid disastrous consequences. 

Packaging, Transport and Dispensing 

Once wine is bottled and beer is packaged, they must be delivered to the relevant outlets. This commonly includes distribution companies, warehousing and in the case of breweries, draymen. Beer and soft drinks use carbon dioxide or a mix of carbon dioxide and nitrogen as a way of delivering a beverage to the ‘tap’. These gases also give beer a longer-lasting head and improve the quality and taste. 

Even when the beverage is ready to deliver, gas-related hazards remain. Those arise in any activity at premises that contain compressed gas cylinders, due to the risk of increased carbon dioxide levels or depleted oxygen levels (due to high levels of nitrogen). Carbon dioxide (CO2) occurs naturally in the atmosphere (0.04%). CO2  is colourless and odourless, heavier than air and if it escapes, will tend to sink to the floor. CO2 collects in cellars and at the bottom of containers and confined spaces such as tanks and silos. CO2  is generated in large amounts during fermentation. It is also injected into beverages during carbonation. 

To find out more on the gas hazards in food and beverage production visit our industry page for more information. 

The importance of Gas Detection in the Water and Wastewater Industry 

Water is vital to our daily lives, both for personal and domestic use and industrial/commercial applications. Whether a facility focuses on the production of clean, potable water or treating effluent, Crowcon is proud to serve a wide variety of water industry clients, providing gas detection equipment that keeps workers safe around the world. 

Gas Hazards 

Apart from common gas hazards known in the industry; methane, hydrogen sulphide, and oxygen, there are bi-product gas hazards and cleaning material gas hazards that occur from purifying chemicals such as ammonia, chlorine, chlorine dioxide or ozone that are used in the decontamination of the waste and effluent water, or to remove microbes from clean water. There is great potential for many toxic or explosive gases to exist as a result of the chemicals used in the water industry. And added to these are chemicals that may be spilled or dumped into the waste system from industry, farming or building work. 

Safety Considerations  

Confined Space Entry 

The pipelines used to transport water require regular cleaning and safety checks; during these operations, portable multi-gas monitors are used to protect the workforce. Pre-entry checks must be completed prior to entering any confined space and commonly O2, CO, H2S and CH4 are monitored. Confined spaces are small, so portable monitors must be compact and unobtrusive for the user, yet able to withstand the wet and dirty environments in which they must perform. Clear and prompt indication of any increase in gas monitored (or any decrease for oxygen) is of paramount importance – loud and bright alarms are effective in raising the alarm to the user. 

Risk assessment 

Risk assessment is critical, as you need to be aware of the environment that you are entering and thus working in. Therefore, understanding the applications and identifying the risks regarding all safety aspects. Focusing on gas monitoring, as part of the risk assessment, you need to be clear on what gases may be present.  

Fit for purpose 

There is a variety of applications within the water treatment process, giving the need to monitor multiple gases, including carbon dioxide, hydrogen sulphide, chlorine, methane, oxygen, ozone and chlorine dioxide. Gas detectors are available for single or multiple gas monitoring, making them practical for different applications as well as making sure that, if conditions change (such as sludge is stirred up, causing a sudden increase in hydrogen sulphide and flammable gas levels), the worker is still protected.  

Legislation   

European Commission Directive 2017/164 issued in January 2017, established a new list of indicative occupational exposure limit values (IOELVs). IOELV are health-based, non-binding values, derived from the most recent scientific data available and considering the availability of reliable measurement techniques. The list includes carbon monoxide, nitrogen monoxide, nitrogen dioxide, sulphur dioxide, hydrogen cyanide, manganese, diacetyl and many other chemicals. The list is based on Council Directive 98/24/EC that considers the protection of the health and safety of workers from the risks related to chemical agents in the workplace. For any chemical agent for which an IOELV has been set at Union level, Member States are required to establish a national occupational exposure limit value. They also are required to take into account the Union limit value, determining the nature of the national limit value in accordance with national legislation and practice. Member States will be able to benefit from a transitional period ending at the latest on 21 August 2023.  

The Health and Safety Executive (HSE) state that each year several workers will suffer from at least one episode of work-related illness. Although, most illnesses are relatively mild cases of gastroenteritis, there is also a risk for potentially fatal diseases, such as leptospirosis (Weil’s disease) and hepatitis. Even though these are reported to the HSE, there could be significant under-reporting as there is often failure to recognise the link between illness and work.  

Under domestic law of the Health and Safety at Work etc Act 1974, employers are responsible for ensuring the safety of their employees and others. This responsibility is reinforced by regulations. 

The Confined Spaces Regulations 1997 applies where the assessment identifies risks of serious injury from work in confined spaces. These regulations contain the following key duties: 

  • Avoid entry to confined spaces, e.g., by doing the work from the outside. 
  • If entry to a confined space is unavoidable, follow a safe system of work.
  • Put in place adequate emergency arrangements before the work start. 

The Management of Health and Safety at Work Regulations 1999 requires employers and self-employed people to carry out a suitable and sufficient assessment of the risks for all work activities for the purpose of deciding what measures are necessary for safety. For work in confined spaces this means identifying the hazards present, assessing the risks and determining what precautions to take. 

Our solutions

Elimination of these gas hazards is virtually impossible, so permanent workers and contractors must depend on reliable gas detection equipment to protect them. Gas detection can be provided in both fixed and portable forms. Our portable gas detectors protect against a wide range of gas hazards, these include T4x, Clip SGD, Gasman, Tetra 3,Gas-Pro, T4 and Detective+. Our fixed gas detectors are used in many applications where reliability, dependability and lack of false alarms are instrumental to efficient and effective gas detection, these include Xgard, Xgard Bright and IRmax. Combined with a variety of our fixed detectors, our gas detection control panels offer a flexible range of solutions that measure flammable, toxic and oxygen gases, report their presence and activate alarms or associated equipment, for the wastewater industry our panels include Gasmaster.    

To find out more on the gas hazards in wastewater and water treatment visit our industry page for more information.  

Gas Hazards in Water Treatment

Water is vital to our daily lives, both for personal and domestic use and industrial/commercial applications. It is everywhere, promoting some chemical reactions and inhibiting others. Being used to clean surfaces, carry chemicals to where they are used and to carry unwanted chemicals away. Do anything and you create a gas somewhere in some quantity. Do anything with water there are so many permutations of things that can come together and react, dissolved gases that can come out of solution, dissolved liquids and solids that can react to generate gases. Additionally, you must determine what gases you generate when you collect, clean, store, transport or use water. Gas detectors must be chosen to suit the specific environment in which they operate, in this case highly humid, often dirty, but rarely outside the temperature range 4 to 30 degrees C. All the risks are present in these complex environments, with multiple toxic and flammable gas hazards and often the additional risk of oxygen depletion.

Gas Hazards

Apart from common gas hazards known in the industry; methane, hydrogen sulphide, and oxygen, there are bi-product gas hazards and cleaning material gas hazards that occur from purifying chemicals such as ammonia, chlorine, chlorine dioxide or ozone that are used in the decontamination of the waste and effluent water, or to remove microbes from clean water. There is great potential for many toxic or explosive gases to exist as a result of the chemicals used in the water industry. And added to these are chemicals that may be spilled or dumped into the waste system from industry, farming or building work.

Chlorine (Cl2) gas appears yellow green in colour, used to sterilise drinking water. However, most chlorine is used in the chemical industry with typical applications including water treatment as well as within the plastics and cleaning agents. Chlorine gas can be recognised by its pungent, irritating odour, which is like the odour of bleach. The strong smell may provide adequate warning to people that they are exposed. Cl2 itself is not flammable, but it can react explosively or form flammable compounds with other chemicals such as turpentine and ammonia.

Ammonia (NH3) is a compound of nitrogen and hydrogen and is a colourless and pungent gas, also known to be highly soluble when in contact with water. This means that NH3 dissolves quickly into the water supply. Found at very low levels in humans and in nature. It is also often used in some household cleaning solutions. Although NH3 has many benefits, it can be corrosive and dangerous in certain circumstances. Ammonia can enter wastewater from several different sources, including urine, manure, cleaning chemicals, process chemicals and amino acid products. If NH3 enters a copper piping system, it can cause extensive corrosion. If NH3 enters water, its toxicity varies depending on the exact pH of the water. It is possible for ammonia to break down into ammonium ions, which can react with other compounds present.

Chlorine dioxide (ClO2) is an oxidising gas commonly used to disinfect drinking water. When used in very small quantities, it is safe and does not lead to significant health risks. But ClO2 is a strong disinfectant that kills bacteria, viruses, and fungi, and when used in high doses, it can be dangerous to people since it can damage red blood cells and the lining of the gastrointestinal (GI) tract.

Ozone (O3) is a gas with an antiseptic smell and no colour that, mostly, forms naturally in the environment. When inhaled, ozone can have a range of harmful effects on the body. As it is colourless gas it is difficult to trace without an effective detection system in place. Even when relatively small amounts are inhaled, the gas can have a damaging impact on the respiratory tract, causing inflammation and chest pain, alongside coughing, shortness of breath and throat irritation. It can also act as a trigger causing diseases such as asthma to worsen.

Confined Space Entry

The pipelines used to transport water require regular cleaning and safety checks; during these operations, portable multi-gas monitors are used to protect the workforce. Pre-entry checks must be completed prior to entering any confined space and commonly O2, CO, H2S and CH4 are monitored. Confined spaces are small, so portable monitors must be compact and unobtrusive for the user, yet able to withstand the wet and dirty environments in which they must perform. Clear and prompt indication of any increase in gas monitored (or any decrease for oxygen) is of paramount importance – loud and bright alarms are effective in raising the alarm to the user.

Legislation

European Commission Directive 2017/164 established an increased list of indicative occupational exposure limit values (IOELVs). IOELV are health-based, non-binding values, derived from the most recent scientific data available and considering the availability of reliable measurement techniques. Non-binding but best practice. The list includes carbon monoxide, nitrogen monoxide, nitrogen dioxide, sulphur dioxide, hydrogen cyanide, manganese, diacetyl and many other chemicals. The list is based on Council Directive 98/24/EC that considers the protection of the health and safety of workers from the risks related to chemical agents in the workplace. For any chemical agent for which an IOELV has been set at Union level, Member States are required to establish a national occupational exposure limit value. They also are required to take into account the Union limit value, determining the nature of the national limit value in accordance with national legislation and practice. Member States will be able to benefit from a transitional period ending at the latest on 21 August 2023.

The Health and Safety Executive (HSE) state that each year several workers will suffer from at least one episode of work-related illness. Although, most illnesses are relatively mild cases of gastroenteritis, there is also a risk for potentially fatal diseases, such as leptospirosis (Weil’s disease) and hepatitis. Even though these are reported to the HSE, there could be significant under-reporting as there is often failure to recognise the link between illness and work.

Under domestic law of the Health and Safety at Work etc Act 1974, employers are responsible for ensuring the safety of their employees and others. This responsibility is reinforced by regulations.

The Confined Spaces Regulations 1997 applies where the assessment identifies risks of serious injury from work in confined spaces. These regulations contain the following key duties:

  • Avoid entry to confined spaces, e.g., by doing the work from the outside.
  • If entry to a confined space is unavoidable, follow a safe system of work.
  • Put in place adequate emergency arrangements before the work start.

The Management of Health and Safety at Work Regulations 1999 requires employers and self-employed people to carry out a suitable and sufficient assessment of the risks for all work activities for the purpose of deciding what measures are necessary for safety. For work in confined spaces this means identifying the hazards present, assessing the risks and determining what precautions to take.

Our solution

Elimination of these gas hazards is virtually impossible, so permanent workers and contractors must depend on reliable gas detection equipment to protect them. Gas detection can be provided in both fixed and portable forms. Our portable gas detectors protect people against a wide range of gas hazards, and include T4x, Clip SGD, Gasman, Tetra 3, Gas-Pro, T4 and Detective+. Our fixed gas detectors are used where reliability, dependability and lack of false alarms are instrumental to efficient and effective protection of assets and areas, and include the Xgard, Xgard Bright and IRmax product ranges. Combined with a variety of our fixed detectors, our gas detection control panels offer a flexible range of solutions that measure flammable, toxic and oxygen gases, report their presence and activate alarms or associated equipment, for the wastewater industry we often recommend our Gasmaster panel.

To find out more on the gas hazards in wastewater visit our industry page for more information.

The problem with “sticky” gases

Reactive or “sticky” gases pose additional issues when it comes to gas detection. As their name suggests, they react with many of the surfaces with which they make contact. This becomes a particular problem if the atmosphere to be tested is being “sampled” rather than tested directly.

Continue reading “The problem with “sticky” gases”

What are VOCs?

The nature of gas hazards posed by some working environments can be complex and complete protection is not available from a single solution. This week, our guest blogger, Richard, takes a look at VOCs: how they pose a hazard and what we can do to protect against them.

Continue reading “What are VOCs?”